FREE Delivery on Orders over €45 just use the code FREE DELIVERY | Irish Owed Company

Register/Sign In | Contact Us

Acousticom 2

155.00 incl. VAT

The Acousticom 2 presents RF measurements (An RF signal is an electromagnetic wave that communications systems use to transport information through air from one point to another.) as an audio signal, with LEDs and an alarm at high levels of RF (you can also switch the sound off if you prefer to be less obvious when taking readings). With simple controls, easy to read results, but still using the same advanced microwave detector as our Acoustimeter, this instrument is perfect for those on a budget. It is smaller and lighter than the Acoustimeter, and comes in its own carry pouch.

Category: Brand:

The Acousticom 2 presents RF measurements as an audio signal, with LEDs and an alarm at high levels of RF (you can also switch the sound off if you prefer to be less obvious when taking readings). With simple controls, easy to read results, but still using the same advanced microwave detector as our Acoustimeter, this instrument is perfect for those on a budget. It is smaller and lighter than the Acoustimeter, and comes in its own carry pouch.

ac2-leds

When first turned on the Acousticom 2 is silent. The sound may be turned on and off by pressing the button. The Acousticom 2 also has an “alarm” sounder which emits a pulsing warning at higher exposure levels.

If the alarm is not required, then it is easy to disable it each time when you turn the Acousticom 2 on. The demodulated sounds allow you to determine, with a small amount of practice, what type of device is creating the pulsing microwave levels that are present. These features make the instrument the most useful and practical one available – even for people with severe electrosensitivity.

Sound samples are available on the “Futher Information” tab to help you identify what kind of signal your Acousticom 2 is measuring. The sounds made by different transmitters can change with time, so these are meant as a rough guide only. If you are subject to a number of sources of RF, the sounds may intermingle and be less easily identified.

The Acousticom 2 reacts to very short pulses. Peak readings are what they say – the highest sampled reading – though the sampling and processing rate means that there are some gaps and it will not always react to a SINGLE VERY short pulse(less than about 5 microseconds duration) – though it will react correctly to much shorter pulses that are regularly transmitted (such as from WiFi).

Please note: The internal antenna is at the upper half of the case and the back. Signals are best measured when the source is behind the instrument, but also quite good with the source to one or other side. Turn the Acousticom 2 for the highest reading.

 

Technical specifications

  • A line of coloured LEDS displaying Peak exposure levels in V/m
  • Measurement range: 200 – 8 000 MHz ±6 dB (typical accuracy)
  • Sensitivity (Peak Display): 0.01 – 6.00 volts per metre (V/m)
    0.01 / 0.02 / 0.05 / 0.1 / 0.3 / 1.0 / 3.0 / 6.0 V/m;
    (equivalent to 0.5 to 100,000 peak µW/m2)
  • Some intermediate points when two LEDs are both lit are also defined: 0.2 / 0.6 / 2.0 / 4.5 V/m
  • The speaker may be switched on and off
  • An alarm sounder at higher exposure levels (may be disabled)
  • Power source: 1x PP3/MN1604 9 volt Alkaline or Rechargeable
  • Battery life: Up to 10 hours continuous with normal alkaline battery
  • » Low battery indicator light (the green ‘on’ light turns red)
  • Size (mm): 110 x 63 x 21 (LxWxD); Weight: 140g incl. battery

Reviews

There are no reviews yet.

Be the first to review “Acousticom 2”

Your email address will not be published. Required fields are marked *